Installing a new roof is a significant investment, particularly with the harsh freeze-thaw cycles we experience in Southeast Michigan. You need a system that handles heavy snow loads and resists wind-driven rain. If you are considering upgrading your home, this standing seam metal roofs step-by-step guide will walk you through the technical reality of the installation process. It is not a weekend DIY project; it requires precision and the right crew. At Best Choice Roofing, we work with these heavy roofing materials daily across Wayne, Oakland, Macomb, and surrounding counties.
For a broader look at the benefits and specifications of this system, check out our comprehensive overview.
Before a single panel is ordered, a thorough inspection of the existing structure is required. In Metro Detroit, we frequently find homes with multiple layers of asphalt shingles. You cannot install standing seam metal roofing over an old, failing deck.
Every project starts with a free inspection. We look for soft spots in the decking, rot in the fascia, and issues with the chimney or vents. Because we do not quote a firm price online, an estimator must evaluate the roof pitch, square footage, and complexity of the flashing details. If we find storm or hail damage—common in our summer storms—we document this immediately to assist with your insurance claim.
Once the scope is defined and the date is set, the crew removes the old materials down to the bare wood sheathing. We strip the property clean of nails and debris, protecting your landscaping and gutters during the process. If the underlying plywood is water-damaged or delaminated, we replace it. Solid decking is non-negotiable for metal roofing; the clips and fasteners need a stable anchor point.
This is the most critical line of defense against ice dams. We install a synthetic underlayment specifically designed for metal roofing. Unlike standard felt paper, high-quality synthetics resist tearing and provide a slip-resistant surface for the crew. In the eaves and valleys—areas prone to ice buildup—we install an ice-and-water barrier. This self-adhering membrane seals around the nails, preventing water from backing up under the metal panels during a thaw.
With a clean, watertight deck prepared, the actual installation of the metal system begins. This phase is where the "standing seam" gets its name.
Before the panels go down, we install the perimeter flashing. This includes the eave strip (drip edge) and the rake edge at the gables. These metal strips direct water away from the fascia and into the gutters. Proper installation here ensures water does not wick back under the roof. Since we also install and repair gutters, we ensure these components work together seamlessly.
Metal roofing expands and contracts with temperature changes. To accommodate this thermal movement, the panels are not screwed down tight. Instead, they use a concealed fastener clip system. We snap chalk lines to ensure the first run of panels is perfectly square. If the first row is off by a fraction of an inch, the error compounds by the time we reach the ridge.
We screw the locking clips into the roof deck. The spacing of these clips is determined by the wind load requirements for your specific area. The clip has a movable part that allows the metal panel to "float" as temperatures shift. This prevents the oil-canning effect (waviness in the metal) and protects the fastener seals from breaking due to stress.
The panels are typically 12 to 16 inches wide and cut to length on-site or ordered to specific measurements. The panel is placed into the clips on one end, and then seamed into the previous panel. The "standing seam" is the raised rib where the panels interlock. This design hides the fasteners completely, eliminating the primary cause of leaks on screw-down metal roofs.
We run the panels all the way to the ridge. In some cases, especially on complex roofs with hips and valleys, we may need to custom-cut flashing to ensure a watertight seal around dormers and skylights.
At the peak of the roof, we install a specialized ridge vent. Metal roofs get hot in the summer, so proper attic ventilation is essential to prevent heat buildup and moisture accumulation. The ridge cap fits over the top of the panels and is secured with concealed fasteners or riveted, depending on the profile. This allows hot air to escape while keeping rain and bugs out.
This step separates a decent roof from a great one. We install custom-fabricated flashing around chimneys, plumbing stacks, and dormers. In standing seam systems, this often involves soldering or using high-grade sealants and counter-flashing to ensure water sheds off these obstacles without entering the seam. If you have active leaks or storm damage, we prioritize these repairs during the installation to prevent future issues.
Once the last piece of trim is up, we perform a final walk-through. We check every seam, verify that the panels are lying flat, and ensure all flashing is secure. Magnetic sweepers are used to grab any stray nails or screws from your driveway and lawn. We haul away all old roofing materials, leaving your property looking as good as, or better than, when we arrived.
Standing seam installation requires specialized tools like seamers, brakes, and notchers. It also requires knowledge of local building codes. In Wayne, Oakland, and Macomb counties, we see wind gusts that can rip poorly installed metal panels right off the deck.
Furthermore, if your roof replacement is the result of storm damage, navigating the insurance claim can be a headache. We provide full insurance-claim help. We meet the adjuster on-site, document the damage, and ensure the scope of work covers the necessary repairs, so you aren't left paying out of pocket for work that should be covered.
A standing seam metal roof is a lifetime investment, but it only lasts if it's installed correctly. We offer same-day response on active leaks and storm damage. Because every roof is unique, we never quote a firm price online. You deserve an accurate assessment based on the actual condition of your home.
If you are ready to upgrade your home or if you need a repair on your current metal roof, contact the licensed and insured crew at Best Choice Roofing.
Call (248) 206-5958 or request a free inspection at roofs.bestchoice411.com.