Ice & Water Shield: Step-by-Step Guide

In Metro Detroit, the freeze-thaw cycles are relentless. If you are replacing a roof in Wayne, Oakland, or Macomb counties, standard underlayment often isn't enough. You need a waterproof barrier to stop ice dams and wind-driven rain. This ice & water shield step-by-step guide outlines the installation process used by professional crews to ensure your home stays dry.

While many homeowners understand the importance of shingles, the membrane beneath them does the heavy lifting. For a comprehensive look at the product itself, check out our overview of ice & water shield.

Why This Installation Matters in Michigan

Before grabbing a utility knife, you need to understand the "why." Ice dams form when heat escapes your attic, melting the snow on your roof. The water runs down to the cold eave and refreezes, creating a dam. Water backs up behind this dam, lifts the shingles, and seeps into the sheathing.

Properly installed ice & water shield creates a self-sealing gasket around nails and prevents this water intrusion. It is a critical component among modern roofing materials designed for harsh climates.

Tools and Materials Needed

To do this correctly, you cannot cut corners. You will need:

Note on Temperature: Most self-adhered membranes require temperatures above 40°F to activate the adhesive properly. In Michigan, if you are installing in late fall or early spring, you may need to store the rolls in a warm room and use a heat gun to aid adhesion.


Step 1: Prep the Roof Deck

Do not apply ice & water shield over a dirty or wet deck. The adhesive will not bond to wet wood or existing felt paper if you are doing a recover (though a full tear-off is standard for Best Choice Roofing).

  1. Sweep the Deck: Remove all nails, staples, wood chips, and debris.
  2. Check for Damage: Inspect the plywood or OSB sheathing. If a section is rotted or water-damaged, replace it before proceeding.
  3. Dry Fit: Ensure the roof is dry. If it rained the night before, let the sun dry the wood before rolling out the membrane.

Step 2: Install the Drip Edge

There is debate among contractors on whether drip edge goes over or under the membrane at the eaves. In Michigan, for maximum ice dam protection, the best practice is often to install the drip edge first at the eaves, then run the ice & water shield over the metal flange. This ensures water cannot wick under the drip edge and into the fascia.

  1. Cut the Drip Edge: Measure the eave length.
  2. Nail it Down: Use roofing nails (galvanized or copper) every 8 to 10 inches.
  3. Corners: Ensure corners are tight or mitered to prevent gaps.

Alternative Method (Code Variance): Some local codes or manufacturers require the membrane to go directly onto the deck, extending over the fascia, with the drip edge installed on top. Verify local requirements in your specific municipality. However, covering the drip edge flange generally offers superior protection against wind-driven rain.

Step 3: Apply the Ice & Water Shield at the Eaves

This is the most critical part of the process.

  1. Measure the Coverage: In Metro Detroit, building codes generally require protection from the eave edge extending at least 24 inches inside the exterior wall line (measured vertically). This is usually a 3-foot wide roll.
  2. Peel and Stick: Remove the split-back release film. Align the bottom edge of the membrane with the drip edge (or the eave edge if skipping drip edge).
  3. Roll it Out: Unroll the membrane along the eave.
  4. Press It Down: Use your hands or a roller to press the adhesive into the decking. Ensure there are no wrinkles or fishmouths (folds that trap water).
  5. Nailing (Minimal): This membrane is self-adhering. You generally do not need to nail it unless the pitch is extremely steep. If you must nail it temporarily to hold it, use plastic cap nails and ensure you seal the heads later with mastic, though ideally, you avoid puncturing the barrier until shingles are installed.

Step 4: Valley Installation (The Open Valley Method)

Valleys are the primary highway for water flow. They require extra care.

  1. Chalk a Line: Mark the center of the valley.
  2. Width: Apply a 36-inch wide (or wider) strip of ice & water shield down the center of the valley.
  3. Overlap: Ensure the membrane from the eave section overlaps the valley section by at least 6 inches. Always overlap up the slope. You want water flowing over the top layer, not seeping underneath.
  4. Press Firmly: Valleys take high water volume. Eliminate all air bubbles.

Step 5: Flashing and Penetrations

Areas around chimneys, skylights, and dormers are failure points.

  1. Flashing: Install metal base flashing where required.
  2. Membrane Over Flashing: Run the ice & water shield over the base flashing. This creates a " sandwich" where the metal provides structure and the membrane provides the seal.
  3. Corners: Cut small triangles (relief cuts) in the membrane at corners so it lays flat against the wall without wrinkling.
  4. Penetrations: For vent pipes or small holes, use a "boot" of ice & water shield or apply a patch of membrane over the flange, extending at least 6 inches in all directions.

Step 6: Rake Edges and Gable Ends

While not always required by code to the same extent as eaves, it is good practice to run ice & water shield up the rake edges (the sloped sides of the roof) about 3 to 4 feet. This protects against wind-driven rain that can blow under shingles during severe Michigan storms.

Common Installation Mistakes to Avoid

When to Call a Professional Roofing Crew

This ice & water shield step-by-step guide demonstrates the logic, but the execution is physically demanding and unforgiving. Once the membrane sticks, it is difficult to reposition. If you make a mistake in the valley or at the eave, you risk extensive interior water damage.

Furthermore, identifying how much protection you need requires a trained eye. If your home in Oakland or Macomb County has poor attic insulation or ventilation, you may be prone to severe ice dams, requiring a higher application of roofing materials (e.g., 6-foot protection instead of 3-foot).

Best Choice Roofing is a licensed, insured Metro Detroit roofing crew serving Wayne, Oakland, Macomb, and surrounding Michigan counties. We specialize in identifying the specific needs of your home.

Our Services Include:

We know that dealing with storm damage is stressful. That is why we offer full insurance-claim help. We handle the paperwork and the adjuster meetings so you don't have to.

If you suspect your roof lacks proper protection or you see signs of ice dam damage, do not wait for the next thaw. We provide same-day response on active leaks and storm damage. We offer free inspections and estimates, and we adhere to upfront pricing—never quoting a firm price online until our roofer confirms the exact scope of work after a thorough, free inspection.


Protect Your Home From Michigan Winters

Don't let ice dams compromise your roof. Call Best Choice Roofing today for a professional assessment.

📞 Call us at (248) 206-5958

📅 Request a free inspection at roofs.bestchoice411.com