If you own a home in Metro Detroit with a low-slope or flat roof, you know that standard asphalt shingles don’t cut it. You need a system that handles standing water, heavy snow loads, and the drastic temperature swings we see in Wayne, Oakland, and Macomb counties. This flat roofing (TPO, EPDM, modified) step-by-step guide covers the entire process, from identifying the right material to the final nail.
At Best Choice Roofing, we treat these projects as structural jobs, not just cosmetic cover-ups. Below is the practical workflow we use to ensure a watertight seal on Michigan homes.
Before any material hits the deck, you have to know what you're dealing with. You cannot choose the right system without a physical inspection.
The Inspection Process We start by looking for the "red flags" specific to flat roofs: ponding water, splits in the seams, and blistering. In Michigan, the freeze-thaw cycle will turn a small crack into a major leak overnight. We check the interior for water stains on the ceiling or damp insulation in the attic.
Choosing the Material Once we assess the deck condition and drainage, we select the material. While we don't quote a firm price online, we help you understand the pros and cons of the primary roofing materials used in our climate:
For a deeper comparison of durability and cost for these specific systems, check out our detailed breakdown of these flat roofing materials.
This is where most failed roofs are born—skimping on the prep. In older Detroit suburbs, you often find multiple layers of old roofing piled up.
Removing the Old Layer We generally tear off everything down to the wood decking. Michigan building code usually allows two layers, but trapping moisture between layers is a recipe for rot. We strip the old TPO, EPDM, or modified bitumen and haul the debris away.
Repairing the Deck With the roof bare, we inspect the sheathing (plywood or OSB). Any soft, wet, or rotted sections are cut out and replaced with new code-compliant decking. If you attach a membrane to rotten wood, the new roof fails immediately. We also ensure the roof deck is securely fastened to the trusses.
A flat roof isn't just a membrane; it’s a system. To meet modern energy codes and protect the membrane, we install insulation.
Iso Board Installation We mechanically fasten or adhere high-density ISO (polyiso) insulation boards. This provides a thermal break and creates a flat surface for the membrane. Flat roofs rarely drain perfectly, so we may taper the insulation systems to create a slight slope toward the drains.
Cover Board On top of the insulation, we often install a cover board (like fiberglass or gypsum). This adds a hard layer that protects the insulation from foot traffic and provides a smooth surface for the membrane adhesion.
The installation technique changes based on the material chosen in Step 1.
For TPO: We roll out the TPO sheets and mechanically fasten them or use adhesive. The critical step is the seam. We use a hot-air welder to fuse the overlapping sheets together. When done correctly, the seam becomes stronger than the sheet itself.
For EPDM: The rubber is laid out and allowed to relax. We then adhere it to the deck. The seams are cleaned with primer and bonded with specialized seam tape. This requires a dry, clean surface to bond permanently.
For Modified Bitumen: We typically use a "torch-down" method (for APP) or hot-mop asphalt (for SBS). The rolls are heated as they are unrolled, melting the asphalt backside to fuse with the base layer. This creates a thick, puncture-resistant barrier ideal for Michigan winters.
Ninety percent of leaks happen at penetrations and edges, not in the middle of the roof. This step requires the most attention to detail.
Penetrations Around vents, plumbing stacks, and HVAC units, we install custom-fitted flashing. For TPO and EPDM, this often involves forming "boots" or pouring liquid flashing to create a seal that moves with the building.
Perimeter Edges Where the roof meets the parapet wall or the fascia, we install metal termination bars. The membrane is wrapped up the wall and clamped down. We then apply a high-quality urethane or mastic sealant to screw heads and top edges. This prevents wind-driven rain from getting under the lip.
Flat roofs must drain, or they will fail. We clean and inspect all drains and scuppers. If the roof has a cricket (a small ridge designed to divert water), we ensure it is directing water away from the chimney or wall.
The Walkthrough Before we leave, we do a magnet sweep to remove all nails and screws. A project manager walks the roof with the homeowner (if safe/accessible) to review the flashing details and ensure the site is clean.
Storm damage is a common reason for needing this guide. If your flat roof was damaged by hail or high winds, the process shouldn't come out of your pocket entirely.
We help homeowners in Wayne, Oakland, and Macomb counties navigate the insurance claim process. We can meet the adjuster on-site to point out damage that might be missed, such as granule loss on modified bitumen or hail strikes on TPO that compromise the membrane integrity. We ensure the scope of work from the insurance company covers the high-quality materials needed for a lasting repair, not just a cheap patch.
This flat roofing (TPO, EPDM, modified) step-by-step guide outlines the technical standards required for a durable roof. However, every home in Detroit is different. A porch roof in Royal Oak requires a different approach than a flat roof garage in Sterling Heights.
Because every project has unique variables—deck condition, access difficulty, and material choice—we never quote a firm price online. A roofer needs to see the deck and measure the square footage to give you an accurate number.
If you have an active leak or see granules in your driveway, don't wait. Water damage spreads quickly in flat roof systems.
Call Best Choice Roofing at (248) 206-5958 or request a free inspection at roofs.bestchoice411.com. We provide same-day response on active leaks, upfront pricing after our inspection, and full support with insurance claims.