If you have spotted water stains on your ceiling or noticed rusted metal around your chimney, you likely need a roof flashing repair step-by-step guide to prevent further damage. In Metro Detroit, where freeze-thaw cycles and heavy storms are common, flashing is often the first line of defense to fail. When the seal breaks or the metal corrodes, water channels directly into your home.
This guide provides practical, actionable instructions for homeowners to handle minor flashing issues. However, roofing work carries significant risk. We will outline when a DIY fix is appropriate and when you need to call a licensed, insured crew like Best Choice Roofing to handle the roof flashing repair safely.
Flashing is the thin metal—usually galvanized steel, copper, or aluminum—installed around roof penetrations. You find it at intersections where the roof meets a vertical surface, such as chimneys, dormers, and skylights, or in roof valleys. Its job is to direct water away from these seams and into the gutters.
When flashing fails, it is usually due to one of three reasons: 1. Corrosion: Rust eats through the metal. 2. Improper Installation: The flashing wasn't layered correctly under the shingles. 3. Loose Fasteners: Nails back out over time, creating gaps.
Before you climb a ladder, gather the necessary materials. For a standard step flashing or chimney flashing repair, you will need:
Do not work on a wet roof. If the shingles are damp or it is actively raining, wait. The risk of slipping is too high. Secure your ladder on firm, level ground.
Climb up and inspect the damaged area. If you are dealing with a simple leak where a piece of flashing has pulled away from the chimney or a vent, proceed. If the damage is extensive—covering a large section of the roof valley or requiring structural replacement—this is a major roof repair best left to professionals.
To replace or repair flashing, you must access the area beneath the shingles. * Use your pry bar to gently lift the shingles covering the top edge of the flashing. * Remove the roofing nails holding these shingles in place. Be careful not to tear the shingle; if they are brittle, they may crack, and you will need replacements. * Set the shingles aside in the order they were removed so you can replace them easily.
Once the shingles are pulled back, inspect the flashing. * If the flashing is rusted through, use your pry bar to lever it out. Remove the old nails holding it to the roof deck or the chimney structure. * If the flashing is simply loose but in good condition, you might only need to re-secure it. However, removing it allows you to reseal the area properly, which is often more effective.
Clean the area thoroughly. Scrape away old roofing cement, tar, and debris. You want a clean, dry surface for the new sealant to adhere to. If you find any rotted wood decking underneath, stop immediately. This indicates a long-term leak that has caused structural damage. At this point, contact a professional for a deck replacement.
Cut your new flashing to fit the space using tin snips. * For Step Flashing (where a roof meets a wall): Slide the new piece of flashing under the siding and over the shingle below it. It should overlap the piece below by at least 2 inches. * For Chimney Flashing: Ensure the flashing is tucked tightly into the mortar joints (counter-flashing) or secured against the brick.
Nail the flashing in place. Critical: Do not nail through the top edge of the flashing where water will flow over it. Nail only the top corner or the side that will be covered by the next shingle or the next piece of flashing.
Apply a generous bead of roofing cement to the underside of the flashing before pressing it down (or over the nails after installation, depending on the specific technique). The goal is to create a watertight barrier.
Once the flashing is secure: * Apply roofing cement to the back of the shingles you removed earlier. * Press the shingles back into place, covering the flashing nail heads. * Nail the shingles down and cover the nail heads with a small dab of cement.
While this guide covers the basics, roofing in Metro Detroit presents specific challenges. Our weather extremes can turn a minor flashing issue into a major emergency overnight.
You should call Best Choice Roofing if: * The roof pitch is steeper than a 6/12 slope (steep enough that you cannot walk on it comfortably). * The leak has caused interior damage or mold growth. * The flashing requires custom fabrication for a unique architectural feature. * You are uncomfortable working at heights.
Best Choice Roofing is a licensed, insured Metro Detroit roofing crew serving Wayne, Oakland, Macomb, and surrounding Michigan counties. We understand that a small flashing leak can quickly lead to thousands of dollars in interior damage if ignored during a heavy spring rain.
We offer same-day response on active leaks and storm damage. Whether you need a simple patch or a full roof replacement, our process is transparent. We provide free inspections and estimates, upfront pricing, and full insurance-claim help if the damage is weather-related.
Because every roof is different, we never quote a firm price online. A roofer must confirm the exact scope and pricing after a free, on-site inspection. We handle services including roof leak repair, storm and hail damage, shingle repair, full roof replacement, flashing, vents, and gutters.
Get Your Free Roof Inspection
Don't let a small flashing leak compromise your home. Call Best Choice Roofing today at (248) 206-5958 or request a free inspection online at roofs.bestchoice411.com.