If you are looking for a seamless gutters step-by-step guide to understand what goes into a proper installation, you are in the right place. In Metro Detroit, we deal with heavy spring rains, freeze-thaw cycles in winter, and the occasional summer storm. Your gutter system is the only line of defense between that water and your foundation. This guide breaks down the exact process a professional crew uses to install seamless gutters, specifically for homes in Wayne, Oakland, and Macomb counties.
For a broader overview of the product and why it outperforms sectional options, you can review our main page on seamless gutters.
Before we get into the installation steps, it is important to understand the difference. Traditional sectional gutters are bought in pieces and snapped together. Those seams are eventually where the leaks happen. Seamless gutters are formed from a single coil of metal on-site. The only seams are at the inside and outside corners. This eliminates 90% of the potential leak points right out of the gate.
A seamless gutter system is custom-built to your house. It cannot be bought off the shelf at a hardware store. The process begins with a thorough inspection.
At Best Choice Roofing, we start by looking at the roofline. We aren't just measuring length; we are checking the fascia board—the wood behind the gutter. If the fascia is rotted due to previous water damage, that needs to be replaced before the new gutters go up. We also calculate the pitch. Gutters aren’t installed level; they need a slight slope (typically 1/4 inch for every 10 feet) toward the downspout to ensure water flows.
We provide free inspections to handle this measurement. During this visit, we will also look at your current gutters & drainage setup to see if downspouts are discharging water too close to the foundation.
Once measured, the next step is selecting the coil. For most Michigan homes, aluminum is the standard choice because it is rust-resistant and cost-effective. However, you have options in thickness (gauge).
This is where the "seamless" magic happens. Our crew arrives with a specialized truck-mounted machine. We feed the flat metal coil into one end of the machine, and it rolls and forms the metal into the gutter shape—usually a "K-style" profile—as it comes out the other side.
We run the metal through the machine to the exact lengths measured in Step 1. Because it is cut to the precise inch of your roofline, there are no gaps along the run.
With the lengths cut, we prep the house. If you have old gutters, we remove them and haul away the debris. We then install a hidden hanger system.
Old school installations often used long spikes and ferrules. Over time, the wood swells and shrinks with the seasons, and those spikes work loose, causing the gutter to sag or pull away from the house. We use screw-in hidden hangers. These are secured directly into the rafter tails (the structural wood of the roof), not just the fascia board. This provides a much stronger hold that prevents sagging under the weight of wet leaves or ice.
We lift the formed sections into place and lock them into the hidden hangers. This is the moment the pitch we calculated earlier is set. We use a level to ensure the water will flow correctly toward the downspout. If the water pools in the gutter, it can breed mosquitoes and, in winter, create ice dams that force water back under your shingles.
Since the gutter is formed in one long piece, we have to manually cut and weld or seal the corners. For inside and outside corners, we use pre-fabricated miters. We seal these joints with a high-grade silicone or gutter sealant and rivet them together for a mechanical hold.
Next, we cut the holes for the downspout outlets. These are typically placed near the ends of the runs or where the roof valley dumps a high volume of water. We attach the outlet and then install the downspout itself. The downspouts are secured to the brick or siding with straps, and we add an elbow at the bottom to direct water away from the home.
The final step in this seamless gutters step-by-step guide is the quality check. We run water through the system to verify flow. We check every corner and miter for leaks. Once the system passes inspection, we clean up any metal shavings or debris created during the cutting process.
We get asked frequently about cost. Because every home is unique—a ranch in Royal Oak has different requirements than a colonial in Rochester Hills—we never quote a firm price online. The price depends on the linear footage, the number of corners, the condition of the fascia, and the material gauge.
However, we do offer upfront pricing. After our free inspection, we give you a written quote. That number does not change unless you decide to add extra work.
It is also worth noting that gutters are often damaged during severe weather. If a tree branch takes out a run of gutters during a storm, or if hail dents the system, your homeowner's insurance may cover the replacement. We provide full insurance-claim help. We can document the damage, meet the adjuster on-site, and help you navigate the paperwork to ensure your claim covers the full scope of the repair.
Even with a professional installation, seamless gutters require maintenance. In the fall, leaves will accumulate. If the downspouts clog, water will overflow. While screens and guards are available, nothing eliminates the need for occasional cleaning entirely.
Inspect your system twice a year. Look for water pouring over the sides during rain (indicating a clog) or streaking on the fascia (indicating a leak).
Get Your Free Gutter Inspection
Best Choice Roofing is a licensed, insured Metro Detroit roofing crew serving Wayne, Oakland, Macomb, and surrounding Michigan counties. We handle everything from roof leak repair and storm damage to full gutter replacements. We offer same-day response on active leaks and storm damage, free inspections and estimates, and upfront pricing.
Don't let poor drainage compromise your foundation.
Call us at (248) 206-5958 or request a free inspection at roofs.bestchoice411.com.