When it comes to protecting a home, the shingles get all the credit, but the metal strips tucked into the joints and valleys do the heavy lifting. If you are looking for a straightforward guide on roof flashing explained, you are in the right place. Here in Metro Detroit, our freeze-thaw cycles and heavy snow loads punish roof systems. Flashing is the primary barrier preventing water from seeping into your attic and walls.
Shingles overlap to shed water, but they are not designed to handle the heavy flow of water in roof valleys or the penetration points around chimneys and vents. That is the job of flashing. Understanding what it is, where it goes, and how to spot failure can save you thousands in water damage repairs.
Flashing is a thin material, usually galvanized steel, aluminum, or copper, that roofers install to direct water away from critical areas of the roof. Think of it as the gutter system within the roof structure itself. It creates a waterproof barrier at intersections and transitions where shingles alone cannot effectively seal the roof.
In Michigan, we rely on flashing heavily because of our weather patterns. When snow melts on a warm roof and refreezes at the eaves (ice dams), water backs up under the shingles. Properly installed flashing creates a secondary defense channel, routing that water back onto the shingles and off the roof, rather than into your living room.
To know what to look for, you need to know what you are looking at. There are several distinct types of flashing used in standard residential roofing:
This is found where a roof slope meets a vertical wall, such as where a dormer window sits on the roof. It consists of rectangular pieces of metal bent at a 90-degree angle. They are "stepped" woven into the shingles—each piece overlaps the one below it. This design ensures water hits the metal and runs down the face of the step flashing rather than slipping behind the wall.
Chimneys are a major leak point because they create a large hole in the roof plane. Chimney flashing is a two-part system usually consisting of base flashing (woven into the shingles) and counter flashing (embedded into the chimney mortar). This sandwich setup locks out water even when the brick structure shifts slightly due to temperature changes.
Valleys are the internal angles where two roof slopes meet. They funnel massive amounts of water. Valley flashing is typically a "W" shaped metal channel laid in the valley before the shingles are installed. In older Metro Detroit homes, you might see open valleys (metal exposed), while newer homes often use closed valleys (shingles cover the metal).
This is the flashing you see around your plumbing vents (the PVC pipes sticking out of the roof) and exhaust flues. It is usually a metal base with a rubber or neoprene boot that stretches around the pipe. The boot is the most common failure point here, as the rubber cracks after years of UV exposure.
Flashing is durable, but it is not invincible. In our service area across Wayne, Oakland, and Macomb counties, we see specific patterns of failure driven by local weather.
You do not need to climb on a ladder to monitor the health of your roof, but you should perform a visual inspection twice a year—spring and fall. Here is an actionable checklist for Metro Detroit homeowners.
Grab a pair of binoculars. Walk around the perimeter of your house and look at the transition points. * Check the Chimney: Look for signs of rusting metal or missing pieces of flashing. Ensure the metal lies flat against the brick. * Check the Valleys: Look for visible gaps, tears in the metal, or heavy accumulation of shingle granules in the valley (which indicates erosion). * Check the Walls: Look for step flashing along the sidewalls. If you see tar or heavy cement globbed on the surface, it is a temporary patch that likely needs permanent correction.
Water often enters through flashing failures and runs down the rafters before showing up on a ceiling. * Attic Check: On a sunny day, turn off the attic lights and look for streams of light coming in around chimneys or vent pipes. If light gets in, water will too. * Stains and Smells: Look for water stains on the rafters or sheathing near the chimney or valleys. A musty smell indicates moisture is getting in, even if you don't see a standing leak yet.
Your gutters impact your flashing. If gutters are clogged, water backs up into the roof edge (eaves) and can seep behind the drip edge flashing. Ensure your downspouts are clear and directing water at least 10 feet away from the foundation.
If you spot rust, loose flashing, or water stains, it is time to call a licensed, insured crew. Flashing repair is not typically a DIY job. It requires lifting shingles without damaging them and working with sheet metal to ensure the water flows the right way.
If you are dealing with an active leak, check out our detailed guide on roof leak repair to minimize interior damage while you wait for a contractor.
Choosing the right team is critical. Flashing work is technical. If a roofer suggests just "mopping over" a flashing problem with tar, get a second opinion. You want a roofer who removes the old materials and installs new metal flashing. For tips on vetting contractors, read our resource on how to choose a roofing contractor.
When we inspect a roof in Metro Detroit, homeowners often ask if we can just fix the flashing. It depends on the roof's age and condition.
Flashing is the unsung hero of your roof. Don't wait for a drip in the bucket during the next heavy rain to address it. Whether you need a quick patch for a vent boot or a complete system overhaul, having a local expert assess the situation is the safest bet.
Best Choice Roofing is a licensed, insured Metro Detroit roofing crew serving Wayne, Oakland, Macomb, and surrounding Michigan counties. We know the local building codes and the specific stress our climate puts on roof flashing. We offer same-day response on active leaks and storm damage, free inspections and estimates, upfront pricing, and full insurance-claim help.
We specialize in roof leak repair, storm and hail damage, shingle repair, full roof replacement, flashing, vents, and gutters. We never quote a firm price online; our roofer confirms exact pricing after a thorough free inspection to ensure accuracy.
Don't risk water damage. Call (248) 206-5958 or request a free inspection at roofs.bestchoice411.com.